The tooth-like metal plate reaches a length of 11inches(30cm), and so it can help increase extra friction between spinning tire and the road surface to gain effective traction force, and finally help driver to get unstuck when bad luch happens. Being made of thick steel means it can withstand even more severe challenges than plastic or Aluminum made products. Travel far with confidence.
Installation and removal is so easy that an average adult can handle it without noticeable strength, within 1-2 minutes. A pair of work glove are included for clean operation. It comes with a compact storage box, and unlike bulky plastic traction board, it takes up very little space in vehicle’s storage compartment.
After installation on the rear tire, it allows the vehicle to move on the road that is too slippery for hundreds of feet (Recommended continuous driving distance: less than 1000 feet). Drivers who use traction mat or recovery board for getting unstuck may need to get out of the vehicle frequently to take back the traction mats or recovery boards that fall behind. With EZUNSTUCK installed, all you need to do is hold the steering wheel tightly, and keep vehicle’s moving speed under 10mph!
There are 5-level adjustable positions as point of joints for installation, in order to adapter to different requirements based on tire width and how the situation would be. You can utilize the extended part of the tooth-like steel board to increase friction and gain extra traction force when necessary. You can install two or more of this product on single or on all wheels that have traction delivered, depending on the specific situation you are in.
It applies to RWD, AWD & 4×4 vehicles such as middle-size to full-size SUV, station wagon, light-duty pickup trucks, full-size van, Cargo van, and other vehicles, as long as they meet the following requirements: 1. It’s rear wheel drive, or all-wheel drive built vehicle; 2. The distance between fender & tire is no less than 2 inches (5cm); the tire thickness is over 4 inches(10cm); and the GVWR/GVM is less than 6500lbs; 3. The puller strap can go through the gap between brake disc & wheel hub.
Getting your vehicle stuck can happen to everyone, no matter how cautious you are. The best way to handle getting stuck in mud, sand, or snow, is to always be prepared for that scenario. EZUNSTUCK can be one of the products in your daily emergency kit.
Model Number: EZ-D02ML
Weight: 7.17kg (medium, set of 2)
Package size: 40x35x10(cm)
It applies to RWD(4×2), AWD & 4×4 vehicles such as middle-size to full-size SUV, station wagon, light-duty pickup trucks, full-size van, Cargo van, and others, as long as they meet the following requirements:
It’s rear wheel drive, or all-wheel drive built vehicle;
The distance between fender & tire is no less than 2 inches (5cm); the tire thickness is over 4 inches(10cm); and the GVWR/GVM is less than 6500lbs;
You can put the puller strap through the gap between brake disc & wheel hub, and the strap can safely go through wheel spokes;
If you own a FWD (front wheel drive) vehicle, and you plan on installing EZUNSTUCK Product to the front tires, remember to drive forward in a straight line, and then remove it before making turns. Otherwise, It will damage the front vehicle fenders!
It can only be installed to the wheel that has engine power transmitted to gain traction;
This product is recommended to be installed to the rear wheel of a RWD/AWD vehicle;
Tire width applicable is 180mm to 270mm; and tire thickness >= 90mm; How to know if my tire are applicable? A tire of “235/55R19” means tire width 235mm, tire thickness 235×0.55=129mm.
This product will not help when the wheel is spinning too long, and vehicle chassis has been supported by road surface. The earlier you apply this product, the better it will work;
Getting unstuck require skilled operation from the driver, and no one can guarantee success every time
What is in the box?
2x traction clip set;
1x Ratchet wrench;
1x Allen Wrench;